← Project L.I.F.T. website

NASA HUNCH · LLASO-P2-XPORT-2026 · Project L.I.F.T.

LIFT Lunar Surface Ops

A south-polar lunar outpost with a three-pad landing field 470 m from the base. Cargo modules land on their own schedule. The LIFT rover picks each one up with its arm and plans a route around craters and boulders. It then docks the module to the nearest free NDS port, including the aft ports of modules that are already docked. Everything runs autonomously. Take the keyboard at any point to drive or to fly the docking mechanism yourself.

Mission clockT+00:00:00
Docked0
Waiting on pads0
ControlAUTONOMOUS
Battery—
Building the lunar surface…

Job —

    Vehicle dynamics 1/6 g · rocker-bogie

    NDS docking IDSS IDD contact limits

    Initial contactLimitLiveAt contact
    Mechanism

    Docking ports

    PortAdapterHostStatusRoute

    Cargo manifest 3,500 kg modules

    ModuleCargoPriorityStatusLocation

    Event log newest first

      Keyboard control after "Take keyboard control"

      Drive
      Drive / reverseW S
      Steer (Ackermann)A D
      Point turnQ E
      BrakeSpace
      Creep mode (0.08 m/s)C
      OutriggersO
      Auto-grab module alongsideG
      Docking mechanism
      Saddle up / downR F
      Saddle traverse left / rightZ X
      Dust covers open / close1
      Soft-capture ring extend / retract2
      Retract + hard capture3
      Seal, leak check, open hatch4
      Deploy legs + release module5
      Saddle clamps open / close6
      Undock module back onto rover7

      Physics. Lunar gravity is 1.62 m/s² with no atmosphere, so dust and plume ejecta fly on pure ballistic arcs. Each of the six wheels samples the terrain under its own contact patch, including small craters, rocks and pebbles. The rocker and bogie angles follow from those contacts. The differential bar averages the two rockers to set body pitch. Every wheel carries its own normal load Ni: the rocker-bogie is solved as a lever about the bogie pivot, then weight shifts fore and aft under acceleration and slopes and side to side in turns (load transfer through the centre-of-gravity height). Each wheel's traction is capped at μi·Ni for the surface under it, with μ = 0.45 on loose regolith, 0.55 on graded road and 0.70 on sintered pads. Traction control shares the drive force by wheel load and hands any excess to wheels with spare grip, so a lightly loaded wheel slips first. Cornering grip is what remains inside each wheel's friction circle. Rolling resistance, grade and per-wheel slip are included. The carried module is its own body on rubber saddle pads (μ 0.6 static, 0.5 sliding) held down by 8 kN of clamp preload: it flexes a millimetre or two under braking and slides if the pad grip is exceeded, for example with the clamps open on a steep downhill stop. Tip-over margin is the lesser of the side and pitch margins from the effective centre of gravity. Terrain. The terrain is procedural, with craters from 1 m to 2 km across. Boulder fields sit on fresh crater rims, and the Moon's curvature is included, which puts the horizon about 2.4 km away. Shading uses a Lommel-Seeliger regolith law with an opposition surge. Terrain shadows are traced for a 9.5° sun. Docking. Ports use the NASA Docking System and International Docking Adapter geometry (IDA-2, IDA-3 and IDA-type passive adapters). Each module carries an active NDS on its nose and a passive IDA on its aft end, so later modules can dock to earlier ones. Contact limits follow the IDSS Interface Definition Document: 0.05–0.10 m/s closing, ≤ 0.10 m lateral, ≤ 0.04 m/s lateral rate and ≤ 4° angular. Modules mate at the hard-capture plane and never pass into the port. Dust covers and a brush-seal boot with 8 clamps, adapted from your GLB's dock, keep regolith off the seals. Masses and drive ratings are notional placeholders for your team to replace.